Check the listing for details. Rak 19007 - WisBlock Starter Kit Mini Box Secured by Screws for Meshtastic. Condition: New. Listed at 24.99 USD. This compact and versatile enclosure is specifically designed to securely accommodate the WisBlock RAK19007 along with a 2000/3000mAh LiPo battery from Makerfocus and includes a dedicated SMA port. Engineered for adaptability, this case enables a streamlined setup for all necessary modules. The enclosure is now secured by screws, ensuring a reliable and robust assembly. Its small size ensures portability, allowing it to easily fit in your pocket, and offers up to 3-4 days of operation on a full charge. The interior provides ample space for additional modules and wiring. **Important Disclaimer:** Please note that this product is intended for use with development boards and is not a plug-and-play solution. Purchasing the case indicates that you already have a functional RAK19007 and simply need a container for it. We are not responsible for any damages, malfunctions, or voided warranties caused by improper use. If you are unsure of your technical abilities, we recommend purchasing a fully assembled device from our store [Available Soon]. Assembly Instructions: 1. Pre-assembly Preparation: - Thoroughly review all instructions before beginning. Steps marked with [OLED] are specific to the OLED variation; skip these for non-OLED setups. 2. Battery Preparation: - Desolder the JST connector from the RAK19007, or carefully remove the plastic casing. - Solder the new battery leads to the designated pins or holes, ensuring correct polarity by referencing the datasheet. - Do **NOT** connect the battery until the LoRa SMA cable is attached and the antenna is installed. 3. Module Connections: - Solder the provided power switch and button according to your specific requirements. - [OLED] Solder the OLED screen to the board, ensuring that the VCC, GND, SCL, and SDA pins are correctly connected. Flip the board over to locate the appropriate pins. 4. OLED Screen Installation [OLED only]: - Insert the 1.3" OLED screen by sliding it into the bottom clips and gently pressing it into the top clips. 5. Final Assembly: - Install all required modules onto the RAK19007. - Secure the RAK19007 into the case. - Press-fit the switch and button bar into place. - Attach the remaining antennas to the board. Install the Bluetooth antenna on the right side and the SMA connector in the top left hole. Refer to the included images for guidance. - Position the battery in the back cover and secure it using double-sided tape. General Wiring Options: - The power switch and button can be configured according to your specific needs. For example: - Use the power switch to toggle the entire device on and off, or to control GPS power. - Program the button to perform additional functions with an IO-XPNDR module, or use it as a reset button. https://store.rokland.com/pages/adding-a-user-button-rak19007 Compatible Modules: - RAK 19007: WisBlock Base Board 2nd Gen - RAK 4631: nRF52840 BLE Core with LoRa SX1262 - RAK 12500: GPS Module - RAK 1904: 3-Axis Acceleration Sensor Compatible Batteries: - Makerfocus 3000mAh LiPo - Makerfocus 2000mAh LiPo Package Includes: Non OLED: •Case Front •Black Case Back •Black Baofeng/Molle Clip •Assembly Instructions •Screws to Close Case Non OLED + Switch: •Case Front •Black Case Back •Black Switch & Button •Black Baofeng/Molle Clip •Assembly Instructions •Screws to Close Case OLED + Buttons: •Case Front •Black Case Back •Black Toggle Switch & Button •Black Baofeng/Molle Clip •Assembly Instructions •Screws to Close Case Non OLED + Antenna: •Case Front •Black Case Back •Black Switch & Button •Black Baofeng/Molle Clip •1x Gizont Antenna •Assembly Instructions •Screws to Close Case Non OLED/SW + Antenna: •Case Front •Black Case Back •Black Switch & Button •Black Baofeng/Molle Clip •1x Gizont Antenna •Assembly Instructions •Screws to Close Case OLED + Antenna: •Case Front •Black Case Back •1x 1.3” OLED Screen •Black Toggle Switch & Button •Black Baofeng/Molle Clip •1x Gizont Antenna •Assembly Instructions •Screws to Close Case