Check the listing for details. Sea Hawk Monterey Bottom Paint. Condition: New. Listed at 59.88 USD. Monterey is Sea Hawk's solvent-free water-based bottom paint that is designed to give the best protection against all types of marine fouling while remaining friendly to the environment. Monterey is a semi-hard, ablative finish that is easy to apply. It is compatible with most paints on the market and can be applied over most existing bottom paint in good condition. Sea Hawk Paints Monterey can also withstand removal from water without affecting its antifouling abilities. Monterey has over 55% copper and is used by Carver Yachts and other yacht builders. Since this water-based bottom paint has extremely low VOC's, it's an excellent choice for the application of bottom paint indoors. Monterey water-based bottom paint comes with a full One Year Manufacturers' Warranty against barnacle growth!California Approved: YesEnvironmentally Friendly: Yes. Solvent-FreeCompare To: Hydrocoat, AquaguardCopper: 54.67% Premium Grade. Highest of any Solvent-FreeUse for Trailer Boats/Power Boats/SailBoats: YesWarranty: Yes. One-Year Written Guarantee Against Barnacle Growth!Rated by Practical Sailor Magazine for 24 Month Protection! *This Item Ships From Florida Please Note: This item is not available to ship to the following states: Arizona, Arkansas, Colorado, Idaho, Indiana,Kansas, Kentucky, Montana, Nebraska, Nevada, New Mexico, North Dakota, Oklahoma, Utah, Vermont, West Virginia, and Wyoming Sea Hawk Paints Monterey Product Information Colors: Black 5445, Blue 5442, Dark Blue 5430, Red 5441, Green 5443Finish/Sheen: Semi-glossConverter: One PackCopper Content: 54.67% (1391 g/l) all colorsVolume Solids: 44% ± 2%Solids by Weight: 78%Mix Ratio: One PackShipping Weight:Black: 21.09 Lbs/Gal (9.56 kg/Gal)Blue: 20.63 Lbs/Gal (9.35kg/Gal)Dark Blue: 20.66 Lbs/Gal (9.37 kg/Gal)Red: 21.22 Lbs/Gal (9.62 kg/Gal)Green: 20.71 Lbs/Gal (9.39 kg/Gal)*All colors are not available in all statesFlash Point: N/AVOC: 78 Grams/LiterTypical Film Thickness:Pleasure craft: 2.2 mils (55.88 μ) dry film thickness (DFT) per coat, (5.0 mils (127 μ) wet film thickness (WFT)), 2 coats on the entire hull, and a 3rd at the waterline and other high wear areas.Pleasure craft (California/Reduced CU2O Leach Rate Application): 1.5 mils (38.1 μ) dry film thickness (DFT) per coat, (3.4 mils (86.36 μ) wet film thickness(WFT)), 2 coats on entire hull.Theoretical Coverage: 320 sq.ft./gal. (29.729 m2) @ recommended film thickness Sea Hawk Monterey ApplicationApply by brush, roller, or spray. Apply 5 mils wet, which will yield 2.2 mils dry per coat.Brush: China BristleRoller: Solvent Resistant Roller Cover 3/8" pile smooth to medium Prewash Roller Cover to remove loose fibers prior to use.Airless Spray: Minimum 33:1 -2 GPM ratio pump; "0.017-0.026" orifice tip; 3/8" ID high-pressure material hose; 90 PSI line pressure; 60 mesh filter.Thinning If thinning is necessary, thin up to a maximum of 10%, with water only.Cleanup Clean all equipment immediately after use with water. It is a good practice to periodically flush out spray equipment during the course of the day. Frequency should depend upon amount sprayed, temperature, elapsed time including delay, etc. Surface PreparationPaint only clean, dry surfaces. Remove all grease, oil, wax, or other foreign material Best to Use Sea Hawk Wax n Grease Solvent Wash S-80 or Low VOC DE-Waxing Etch & Cleaner S-90, or detergent washing. (SSPC-SPI).New Construction: Dependent on yard procedures, consult your Sea Hawk Representative.Previously Painted Surfaces: If the previous coating is known to be compatible (See SeaHawk Compatibility Chart) and in good condition, scuff sand with 80 grit sandpaper then solvent clean with SeaHawk S-80 Wax "N" Greaser to remove residue. In poor condition remove antifouling with SeaHawk 1280 Marine Stripper. For any questions please contact Bottom Paint Store.