Check the listing for details. Winwing Joystick Base to Thrustmaster Joystick Grip Conversion Extension. Condition: New. Listed at 45.94 USD. This plug and play Conversion Extension enables a Thrustmaster Joystick Grip to be used on a Winwing Joystick Base (where firmware allows). The main tube is 30mm in diameter and comes in a choice of 3 different heights, 50mm, 75mm and 100mm. Unlike most others available, this Conversion Extension is fully hardwired allowing easy no-fuss swap out. The plug on the Conversion Extension can be rotated to suit the orientation of the socket on the Winwing original bases. This is necessary as the rotation of the socket in some Winwing Bases differ from others, even the same models. DO NOT OVER ROTATE the plug in the Conversion Extension when aligning, just rotate enough to line it up properly. Spinning it around for laughs will break the wiring eventually causing failure. A 0.5mm rubber washer is supplied to be placed at the bottom of the Conversion Extension (Winwing side) to aid in the prevention of rotation when tightened. This Conversion Extension can be used in conjunction with other extensions designed for Winwing or Thrustmaster by placing it either on top of a Winwing (or compatible) extension or at the base of a Thrustmaster extension. * NOTE, the Conversion extension is compatible with ALL QR4rigs extensions when used with a Winwing Joystick Base and Thrustmaster Grip. **NOTE about Virpil Grips: Winwing firmware identifies Virpil (VPC) grips as TM Grips in general, therefore will only be as functional as putting the Virpil Grip on a TM base e.g. some of the extra axis and buttons will not be functional. This is a limitation of the firmware in the WW base and is not changed by the Conversion Extension. NOTE. Winwing firmware needs to be up to date and the Conversion Extension will only work as well as the firmware allows. Compatibility NOTE: Our conversion extensions are not compatible if the MFSSB Kit is installed. Winwing Joystick Bases and Thrustmaster Joystick GripsWinwing ExtensionsQR4rigs Thrustmaster extensions*QR4rigs Winwing extensions*Partial support for Virpil Grips**No other bases or grips are considered compatible at this time. Winwing Bases Super Libra Joystick BaseOrion 2 Joystick Base Thrustmaster Grips Thrustmaster Warthog GripThrustmaster F/A-18C GripThrustmaster Cougar Grip Partial support for Virpil Grips** (see Notes above) VPC WarBRD GripVPC V.F.X GripVPC MongoosT-50 Series GripsVPC Constellation ALPHA Series GripsVPC Constelation DELTA Naming Convention Model Height WW2TM50 50mm WW2TM75 75mm WW2TM100 100mm IMPORTANT - Installation Instructions (scan the barcode on the packaging to get a copy of these instructions): The Conversion Extension must be installed on the base or extension (A) before adding the grip (B).Do not overtighten the grub screw on the WW Base or WW ExtensionRotate only the knurled screw nuts.DO NOT ROTATE THE CONVERSION EXTENSION or the GRIP!DO NOT OVER ROTATE the plug in the extension when aligning with base.Take care to align the plugs and sockets to avoid damaging them.A rubber washer is supplied with the kit making a much tighter connection between the mating surfaces, so much so, that using and tightening the grub screw on the base is now optional.NOTE about Virpil Grips: Winwing firmware identifies Virpil (VPC) grips as TM Grips in general, therefore will only be as functional as putting the Virpil Grip on a TM base e.g. some of the extra axis and buttons will not be functional. This is a limitation of the firmware in the WW base and is not changed by the Conversion Extension. A. Conversion Extension Installation to Winwing Base If installed, loosen the grub screw so that it is clear of the internal threads on the Knurled Base Screw on the base.Place the rubber washer on top of the mating surface on the base around the socket.Carefully align the plug on the base of the conversion extension with the socket in the Winwing base. When aligned it should go in easily and the mating surfaces should be flat.Turn the conversion extension to the desired orientation and hold in place. DO NOT over rotate the conversion extension.Tighten the knurled base screw by hand, whilst holding the conversion extension still. Do not use tools on the knurled base screw but make sure it is tight. The grub screw (or grub screw hole should align with the metal catch plate at either the front or the back of the conversion extension.(optional) Install and tighten the grub screw. Do not overtighten the grub screw, to the pinch is adequate. B. Thrustmanster Grip Installation to Conversion Extension Carefully align the plug with the socket of the extension.When aligned the mating surfaces should be flat.DO NOT rotate the conversion extension or the grip, only turn the knurled screw.Tighten the knurled screw by hand, whilst holding the extension pole and grip still. Do not use tools on the knurled screw but make sure it is really tight. We usually only print one of each model ahead of time to keep costs as low as possible, so if the model you require is showing as out of stock, we have probably just sold it, please drop us a message and we will endeavor to manufacture another as a priority. If you need a different height, please get in touch! IMPORTANT NOTE: Our extensions are not compatible if the MFSSB Kit is installed. Note: This item is 3D printed. There will be obvious print lines on this product due to the nature of 3D printing. The colour of the base interface, plug and socket holder (not visible once installed) will vary depending on model chosen. We have colour coded them to make sure we send you the right one!